Electric Motor, Pump, Heater, Car Part, Dayton, Trane, John Deere Valve, Watts, Inverter, Controller, Genteq, Carrier, Industrial Products Burks 350CS9M-AB-FE Bronze Turbine Pump 350CS9M 120946 Crane 5HP 3PH – First Rate Parts
The best way to find the part you are looking for is to search in this bar by part number, brand, or key word
Cart 0
Burks 350CS9M-AB-FE Bronze Turbine Pump 350CS9M 120946 Crane 5HP 3PH

Crane

Burks 350CS9M-AB-FE Bronze Turbine Pump 350CS9M 120946 Crane 5HP 3PH

$2,099.99 $3,785.00

Burks 350CS9M-AB-FE Bronze Turbine Pump 120946 Crane 5 HP 3PH 208 230 460 NEW  

LAST ONE!!!

IN STOCK, Ships immediately!!

This is the CHEAPEST price ANYWHERE on a genuine part.

This is new, never used or installed.

THIS IS A GENUINE OEM BURKS PUMP!! THIS IS NOT A CHEAP AFTERMARKET OR USED PART THAT WILL NOT LAST AND WILL NEED REPLACED!! DON'T WASTE TIME, MONEY, AND HASSLE REPLACING IT AGAIN!!!

Ships in generic bulk packaging.

Get the best price ANYWHERE HERE!!!

Get your genuine high end part for much cheaper here.  Don't worry about old used parts breaking, this is brand new.  Don't settle for used parts this is brand new.  BETTER BUILT!!!

This part sells for over $3785

All returns must be returned in the original as received uninstalled condition with all accessories, components, and packaging. Items must be well packaged and insured. Buyers are responsible to ensure that items are received back to us in the original undamaged condition. Buyer is responsible for all shipping costs. Buyer must retain all packaging for an item damaged in shipment. A shipping claim cannot be processed without original packaging and hence the item cannot be returned or refunded.

Fits: (may fit various models, you are responsible to verify this is the correct part number for your application)

The Burks 350CS9M-AB-FE is an All Bronze Turbine Pump and FE Motor with a Bronze Impeller, Buna-N/Carbon/Ceramic/SS Mechanical Seal, 1-1/4 Inch NPT Inlet, 1 Inch NPT Outlet Ports, close coupled to a 5 Horsepower, 3500 RPM, 208-230/460 Volts, 3 Phase, ODP Open Drip Proof, 60Hz Motor. This pump has a maximum performance of up to 20 gallons per minute water flow at 350 feet of head (151 PSI). The motor on this pump has open drip proof construction and is rated with jet pump service factors for continuous duty operation at all ratings shown. The three phase motor on this pump requires a magnetic type starter which provides full 3-leg overload protection. This pump is an All Bronze version with the non-standard -FE motor which is the OEM version. The operating temperature limits for this All Bronze pump with the Buna-N seal is 225 degrees F (107 degrees C). Bronze pumps are suitable for most common liquids in the pH range from 4-11. This compact turbine pump is designed for pumping clear water and many other nonabrasive, lower viscosity liquids on high pressure, low capacity applications with the greatest possible efficiency. The Bronze impeller with Monel blades is the only moving part and the Bronze raceway with cast-in vortex pockets will not vapor lock. This pump's unique design is engineered for many applications requiring higher pressures and lower capacities impossible for other single stage pumps of a similar size, and the pump's compact space-saving size without a coupling eliminates misalignment problems. The pump shaft seal is a mechanical seal with ceramic seat and carbon seal face for maximum durability, and long trouble-free service. While this pump can be run dry for short periods of time, a lack of liquid will damage the Mechanical seal. The wetted material in contact with the liquid are Bronze, 303 Stainless Steel, and Buna-N. The dimensions of this pump are 21 inches long, 9 inches high, and 6-1/2 inches wide.
WEIGHT : This pump and motor unit weighs 75 Lbs.

NOTE: A strainer, approximately 20 mesh, should be installed on the suction side of the pump to prevent chips, scale or hard foreign particles from entering the pump and damaging the raceway and impeller.

Features :

Pump Body:
Bronze

 

Impeller:
Bronze

 

Shaft Seal:
Buna/N/Carbon/Ceramic/SS Mechanical Seal

 

Port Size:
Ports are 1-1/4 Inch NPT Inlet, 1 Inch NPT Outlet

 

Motor / Amp Draw:
5 Horsepower, 3500 RPM RPM, 208-230/460 Volts, Three Phase, ODP Open Drip Proof.


Product Specs :

Raceway Sealing grooves, machined into the face of the raceway, match the impeller sealing grooves, minimizing water slippage and increasing delivery efficiencies.

Impeller Annular grooves or sealing rings, machined into the face of the impeller are perfectly matched with corresponding grooves in the raceway and intermesh without metal-to-metal contact to form a labyrinth seal.

Extended LifeLok adjustment allows for extendeded life, field adjustment, and restoring factor efficiency as hydraulic passage wears.


Share this Product


More from this collection